Paldiski mnt.26A, Tallinn
+372 50 64 135 The essential technical characteristics of universal 70 gsm Double A paper, determining the smooth and continuous usage (simplex and duplex) and the contact between all the office equipment and paper, are superior to lower and 80 gsm paper of the same qualitative class from the standard European mills that often use a mixed softwood and hardwood pulp. In fact the “runnability” of paper inside the office equipment depends not on the nominal grammage, but on the other physical parameters of paper, therefore it is worth to change the psychological attitude towards the 70 gsm paper!
– What is 70 gsm paper in comparison to 80 gsm?
Less wood, less paper waste, less energy and water and lower CO2 emission!
– 70 gsm paper – even more efficient ecological production cycle of farmed trees!
It is green product for your green office!
– The success formula of 70 gsm paper:
Less weight = less resources and waste!
The direct advantage for you with 70 gsm:
– Less weight = more prints for customer per same minute! (More copies with high-speed office equipment compared with 80 gsm paper!)
– Less weight = more stapled sheets of paper per one time!
– Less weight = more sheets (up to 20%) put safely in your archive box!
With 70 gsm Double A paper – all of top Double A company quality standards retained.
Paper Double A (A category), A4, 70g, 500 sheets
5,84 €
938 in stock
Description
Additional information
| Weight | 2,5 kg |
|---|---|
| Dimensions | 300 × 215 × 70 cm |
| Бренд |
Related products
Tindipea välispuhastuseks vedelik OCP Pink, 250ml
[:et]Cleaning Fluid for outside cleaning of inkjet cartridges, especially plastic surfaces\.
Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
EAN:0
[:ru]Cleaning Fluid for outside cleaning of inkjet cartridges, especially plastic surfaces\.Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
EAN:0
[:en]Cleaning Fluid for outside cleaning of inkjet cartridges, especially plastic surfaces\.Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
EAN:0
[:] 
Koopiapaber Navigator Universal A4 80g 2500 lehte – kast
[:et]Ideaalne paber igapäevaseks kopeerimiseks\. Suuremahulised kopeerimised\. Alati kõrgekvaliteediline tulemus kõikide kontorimasinatega\. Sobib nii laser- kui tindiprinterisse\.
Kastis on 5 pakki x 500 lehte
Kasutus:
Vahelehed, arved, käsiraamatud, suuremahulised postitused, memod, igapäevane trükkimine ja koopiate tegemine
Keskkond:
ISO 14001, EMAS, FSC, PEFC, Põhjamaade luik, EU lill, TCF, ECF, ISO 9706 , ColorLock tehnoloogia\.
Telli kaks kasti paberit ja toome Tallinna piires tasuta\. Küsige eraldi arvet\.
info@printok\.ee
Kastis on 5 pakki x 500 lehte
Kasutus:
Vahelehed, arved, käsiraamatud, suuremahulised postitused, memod, igapäevane trükkimine ja koopiate tegemine
Keskkond:
ISO 14001, EMAS, FSC, PEFC, Põhjamaade luik, EU lill, TCF, ECF, ISO 9706 , ColorLock tehnoloogia\.
Telli kaks kasti paberit ja toome Tallinna piires tasuta\. Küsige eraldi arvet\.
info@printok\.ee
Kastis on 5 pakki x 500 lehte
Kasutus:
Vahelehed, arved, käsiraamatud, suuremahulised postitused, memod, igapäevane trükkimine ja koopiate tegemine
Keskkond:
ISO 14001, EMAS, FSC, PEFC, Põhjamaade luik, EU lill, TCF, ECF, ISO 9706 , ColorLock tehnoloogia\.
Telli kaks kasti paberit ja toome Tallinna piires tasuta\. Küsige eraldi arvet\.
info@printok\.ee
Kastis on 5 pakki x 500 lehte
Kasutus:
Vahelehed, arved, käsiraamatud, suuremahulised postitused, memod, igapäevane trükkimine ja koopiate tegemine
Keskkond:
ISO 14001, EMAS, FSC, PEFC, Põhjamaade luik, EU lill, TCF, ECF, ISO 9706 , ColorLock tehnoloogia\.
Telli kaks kasti paberit ja toome Tallinna piires tasuta\. Küsige eraldi arvet\.
info@printok\.ee
EAN:0
[:ru]Ideaalne paber igapäevaseks kopeerimiseks\. Suuremahulised kopeerimised\. Alati kõrgekvaliteediline tulemus kõikide kontorimasinatega\. Sobib nii laser- kui tindiprinterisse\.Kastis on 5 pakki x 500 lehte
Kasutus:
Vahelehed, arved, käsiraamatud, suuremahulised postitused, memod, igapäevane trükkimine ja koopiate tegemine
Keskkond:
ISO 14001, EMAS, FSC, PEFC, Põhjamaade luik, EU lill, TCF, ECF, ISO 9706 , ColorLock tehnoloogia\.
Telli kaks kasti paberit ja toome Tallinna piires tasuta\. Küsige eraldi arvet\.
info@printok\.ee
EAN:0
[:en]Ideaalne paber igapäevaseks kopeerimiseks\. Suuremahulised kopeerimised\. Alati kõrgekvaliteediline tulemus kõikide kontorimasinatega\. Sobib nii laser- kui tindiprinterisse\.Kastis on 5 pakki x 500 lehte
Kasutus:
Vahelehed, arved, käsiraamatud, suuremahulised postitused, memod, igapäevane trükkimine ja koopiate tegemine
Keskkond:
ISO 14001, EMAS, FSC, PEFC, Põhjamaade luik, EU lill, TCF, ECF, ISO 9706 , ColorLock tehnoloogia\.
Telli kaks kasti paberit ja toome Tallinna piires tasuta\. Küsige eraldi arvet\.
info@printok\.ee
EAN:0
[:] 
Tindipea välispuhastuseks vedelik OCP Pink, 1L
[:et]Cleaning Fluid for outside cleaning of inkjet cartridges, especially plastic surfaces\.
Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
EAN:0
[:ru]Cleaning Fluid for outside cleaning of inkjet cartridges, especially plastic surfaces\.Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
EAN:0
[:en]Cleaning Fluid for outside cleaning of inkjet cartridges, especially plastic surfaces\.Instruction for use:
Pour a little fluid on a cloth or paper towel\.
Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.
Clear up the nozzles area\.
EAN:0
[:] 
Fotopaber Barva Glossy, 230 g/m², A4, 50 lehte
[:et]Reeglina on soovitatav printida tekstidokumente, illustreeritud jooniseid, graafikuid ja jooniseid, samuti plakateid ja värvibrošüüre\. Mahlased värvid ja teravad jooned tõmbavad selle paberi poole professionaale\. Kahepoolsed mattpaberi tüübid võimaldavad teil kasutada paberi mõlemat külge, ilma et saaksite märjaks saada, mis on õnnitluskaartide, voldikute, portfellide valmistamisel väga oluline\. Barva glossypaber sobib nii vees lahustuvate kui ka pigmendivärvidega\. Toetab kõrge eraldusvõimega printerit 5760\+ dpi\.
EAN:0
[:ru]Reeglina on soovitatav printida tekstidokumente, illustreeritud jooniseid, graafikuid ja jooniseid, samuti plakateid ja värvibrošüüre\. Mahlased värvid ja teravad jooned tõmbavad selle paberi poole professionaale\. Kahepoolsed mattpaberi tüübid võimaldavad teil kasutada paberi mõlemat külge, ilma et saaksite märjaks saada, mis on õnnitluskaartide, voldikute, portfellide valmistamisel väga oluline\. Barva glossypaber sobib nii vees lahustuvate kui ka pigmendivärvidega\. Toetab kõrge eraldusvõimega printerit 5760\+ dpi\.EAN:0
[:en]Reeglina on soovitatav printida tekstidokumente, illustreeritud jooniseid, graafikuid ja jooniseid, samuti plakateid ja värvibrošüüre\. Mahlased värvid ja teravad jooned tõmbavad selle paberi poole professionaale\. Kahepoolsed mattpaberi tüübid võimaldavad teil kasutada paberi mõlemat külge, ilma et saaksite märjaks saada, mis on õnnitluskaartide, voldikute, portfellide valmistamisel väga oluline\. Barva glossypaber sobib nii vees lahustuvate kui ka pigmendivärvidega\. Toetab kõrge eraldusvõimega printerit 5760\+ dpi\.EAN:0
[:] 
Tindipea sisepuhastuseks vedelik OCP Yellow, 1L
[:et]Print head Cleaning liquid instructions\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
EAN:0
[:ru]Print head Cleaning liquid instructions\.Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
EAN:0
[:en]Print head Cleaning liquid instructions\.Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
EAN:0
[:] 