Paldiski mnt.26A, Tallinn
+372 50 64 135
Photo paper Barva Profi Super Glossy, 255 g/m², A3, 20 sheets
25,54 €
11 laos
Lisainfo
| Kaal | 0,250 kg |
|---|---|
| Mõõtmed | 430,000 × 310,000 × 20,000 cm |
| Bränd |
Seotud tooted
Koopiapaber Navigator Universal A4 80g 2500 lehte – kast
Ideaalne paber igapäevaseks kopeerimiseks\. Suuremahulised kopeerimised\. Alati kõrgekvaliteediline tulemus kõikide kontorimasinatega\. Sobib nii laser- kui tindiprinterisse\.
Kastis on 5 pakki x 500 lehte
Kasutus:
Vahelehed, arved, käsiraamatud, suuremahulised postitused, memod, igapäevane trükkimine ja koopiate tegemine
Keskkond:
ISO 14001, EMAS, FSC, PEFC, Põhjamaade luik, EU lill, TCF, ECF, ISO 9706 , ColorLock tehnoloogia\.
Telli kaks kasti paberit ja toome Tallinna piires tasuta\. Küsige eraldi arvet\.
info@printok\.ee
Kastis on 5 pakki x 500 lehte
Kasutus:
Vahelehed, arved, käsiraamatud, suuremahulised postitused, memod, igapäevane trükkimine ja koopiate tegemine
Keskkond:
ISO 14001, EMAS, FSC, PEFC, Põhjamaade luik, EU lill, TCF, ECF, ISO 9706 , ColorLock tehnoloogia\.
Telli kaks kasti paberit ja toome Tallinna piires tasuta\. Küsige eraldi arvet\.
info@printok\.ee
EAN:0
STANGER Disinfectant Cleaner for hands and surfaces Disinfectant Cleaner, 200 ml 3 pcs
STANGER Disinfectant Cleaner for hands and surfaces Disinfectant Cleaner, 200 ml 3 pcs
Rapid disinfectant cleaner removes effectively bacteria, yeasts,
fungi and viruses on surfaces\. Spread the cleaner carefully on the area
to be cleaned\. DGHM VII certified\.
Contains biocidal products 70% ethanol 642\. 0\.03 % hydrogen peroxide \(WHO-Recomendation\)
Shelf life 3 years when stored corectly\.
Approval number:
ChemBiozidMeldeV
N-87506
Biodegradable\.
EAN:0
STANGER Disinfectant Cleaner for hands and surfaces Disinfectant Cleaner, 200 ml
STANGER Disinfectant Cleaner for hands and surfaces Disinfectant Cleaner, 200 ml
Rapid disinfectant cleaner removes effectively bacteria, yeasts,
fungi and viruses on surfaces\. Spread the cleaner carefully on the area
to be cleaned\. DGHM VII certified\.
Contains biocidal products 70% ethanol 642\. 0\.03 % hydrogen peroxide \(WHO-Recomendation\)
Shelf life 3 years when stored corectly\.
Approval number:
ChemBiozidMeldeV
N-87506
Biodegradable\.
EAN:0
Tindipea puhastusvedelik OCP “Nozzle Rocket”, 1L
Liquid is designed for unclogging \(internal rinsing\) of ink cartridges\. Its specially working out chemical composition allows to remove \(dissolve\) very precisely the reminders of dry ink from the cartridge\.
This liquid is an auxiliary liquid and should be used jointly with
OCP
internal yellow liquid\. Simply -
Nozzle Rocket
removes all the dry ink remainders which wasn't dissolved after use of yellow liquid\. Use
Nozzle Rocket
liquid only injecting it inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature
55 °C
\. It is very important not to cross that temperature! Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\. Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device through the exhaust nozzles \(alternatively using specialist suction device\)\.
ATTENTION
: We receive the largest effectiveness when the liquid is heated to
55 °C
\. Don´t cross that temperature! After cartridge rinsing with
Nozzle Rocket
liquid, it is recommended removing liquid reminders injecting inside the cartridge distilled water and removing reminders sucking it off through exhaust nozzles\.
EAN:0
Tindipea sisepuhastuseks vedelik OCP Yellow, 250ml
Print head Cleaning liquid instructions\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
EAN:0