Lomond Inkjet Mini Album Small Heart Matte 32x40mm (Small)

 The essential technical characteristics of universal 70 gsm Double A paper, determining the smooth and continuous usage (simplex and duplex)

Kvaliteetse fototrüki jaoks peab teil olema hea printer, kvaliteetne tint ja muidugi ka kvaliteetne fotopaber\. Ainult kvaliteetne fotopaber suudab pildivärvide täielikku heledust täielikult edastada, et foto püsiks pikka aega hele ja värske\.

Fotopaber Barva Läikiv 200 g / m² A4 20l\. sobib printimiseks kõigile tindiprinteritele\. Te ei kahetse, kui kasutate seda paberit paljude värvide ja toonidega küllastunud piltide ja fotode printimiseks\. Sellel on mõõdukas läige ja kõrge imavus\. Barva läikival fotopaberil imendub tint kiiresti ja teie fotod on minutitega valmis\.

Läikiva BARVA fotopaberi eelis: trükitud pildi kiire kuivamine; ühilduvus pigmenteerunud ja vees lahustuvate tintidega; täiuslikult edastab erksaid ja küllastunud värve; sobib kasutamiseks mis tahes tindi ja kassetiga tindiprinterites; optimaalne printeri 5760\+ eraldusvõimega printimiseks\. Trükkimiseks kasutatakse läikivat paberit: fotod; ajakavad ja esitlused; tekst mis tahes värvipilt\.

Soovitame paberit hoida kuivas kohas, otsese päikesevalguse eest kaitstult\. Ei sisalda kahjulikke aineid\. Prinditud pilte on soovitatav säilitada albumites või klaaside all raamides\. Kõrge prindikvaliteedi saavutamiseks kasutage tindiprinteris või MFP-s õigeid sätteid

Print head Cleaning liquid instructions\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.

Some contaminations:


Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)

after that period wipe near exhaust nozzles using a piece of cloth\.


Large contaminations:


Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours


CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.

Procedures with solid print heads \(Epson models\)\.

Proceed according to the following recommendations:

Start printing

During printing, take out plug from power cord \(the print head should be in a central position\)

Cut out a piece of cloth in the shape of print head

A piece of cloth must be soaked with liquid

put it on the park place \(usually at the right side of the printer\)

Shift the print head in the park position

Wait about 30 minutes

Remove a piece of cloth

Plug the printer in\.

Cleaning Fluid for outside cleaning of inkjet cartridges, especially plastic surfaces\.
Instruction for use:


Pour a little fluid on a cloth or paper towel\.

Put the cartridge on the paper towel or cloth for few minutes in position like cartridge is in a printer\.

Clear up the nozzles area\.