Paldiski mnt.26A, Tallinn
+372 50 64 135
Top sell
New products
Secabo TP10 pneumatic heat press 80cm x 100cm
The newly developed heat press Secabo TP10 is for professional textile printers of large objects: With an extra large work area of 80 x 100 cm, the transfer press is particularly suitable for heat transfers on expansive media such as flags, sheets or room dividers made of textile\. The base plate acts as a drawer, which allows comfortable arranging of transfer objects and can be handled despite its size with little effort\. The pressure of the TP10 transfer press is produced by compressed air, which means working with consistent and reproducible results\. The pneumatic head of the heat plate allows due to vertical contact pressure a flawless transferring of various materials without displacement effects, etc\. The Secabo TP10 heat press with a heat output of 5\.1 kW is suitable for all standard transfer processes and thus can be used in almost all areas of technology transfer\.
Extra large work surface 80cm x 100cm
Base plate designed as a drawer - plenty of space for arranging the transfer objects
Digital controller for temperature, time and counting of pressing operations
Pneumatic pressure easily adjustable and reproducible
Suitable for high workload in production
Extra large work surface 80cm x 100cm
Base plate designed as a drawer - plenty of space for arranging the transfer objects
Digital controller for temperature, time and counting of pressing operations
Pneumatic pressure easily adjustable and reproducible
Suitable for high workload in production
EAN:PIGU35288116
Tindipea sisepuhastuseks vedelik OCP Yellow, 1L
Print head Cleaning liquid instructions\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
EAN:0
