Paldiski mnt.26A, Tallinn
+372 50 64 135
Top sell
New products
Secabo TC1 transfer press 15cm x 15cm
The TC1 heat press from Secabo has a working surface of 15 x 15 cm\. This makes it perfect for textile finishing, e\.g\. for emblems, patches, iron-on pictures, branding or product labeling\. The TC1 is lightweight and very compact, making it just right for mobile use at events\. Our "little one" is also ideal as an inexpensive entry-level model\. The TC1 masters transfers on hard-to-reach areas, it presses specifically where it is desired and necessary\. This prevents resublimation and dye migration in particular\. The plate heats up quickly and has a low energy consumption\. As usual from Secabo, the TC1 is easy and can be operated even by beginners\. The large opening angle allows transfer objects to be conveniently prepared on the base plate\. Time and temperature for the transfer can be precisely preselected on the digital controller\. The contact pressure is set by handwheel\. Closing the press lever starts the pressing process\.
For small emblems, patches, branding etc\.
Inexpensive heat press for beginners or as a mobile additional device
Compact dimensions, low weight
Low energy consumption
Large opening angle
Digital controller for temperature and time
Heats quickly up to 210 °C
For small emblems, patches, branding etc\.
Inexpensive heat press for beginners or as a mobile additional device
Compact dimensions, low weight
Low energy consumption
Large opening angle
Digital controller for temperature and time
Heats quickly up to 210 °C
EAN:PIGU35288116
ANALOOG TINDIKASSETT HP 82 Cyan
HP Designjet 10ps
HP Designjet 20 PS
HP Designjet 50 PS
HP Designjet 111
HP Designjet 120
HP Designjet 120nr
HP Designjet 500
Designjet 500 Plus, Designjet 500PS, Designjet 500 PS Plus
HP Designjet 510
Designjet 510PS
HP Designjet 800
Designjet 800PS
HP Designjet 815
HP Designjet 820
HP Designjet 111 610mm
HP Designjet Copier CC 800PS
EAN:PIGU35283986
Tindipea sisepuhastuseks vedelik OCP Yellow, 1L
Print head Cleaning liquid instructions\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
Replaceable print heads \(Hewlett Packard, some Lexmark series, Canon 2000 / 4000 / 5000 series\)\.
Some contaminations:
Soak the towel in the unclog printhead liquid and leave the print head \(on the towel\) in position like inside the printer for 15-30 minutes \(maximum 2 hours\)
after that period wipe near exhaust nozzles using a piece of cloth\.
Large contaminations:
Fill the flat dish with liquid and put the print head in position like inside the printer for up to 12 hours
CAUTION:
Do not sink the cartridge in the liquid at the level as the print head nozzles are located\. It may damage \(separate\) plastic parts of the cartridge\. Internal liquid may be injected inside the cartridge\. We receive the best effectiveness when liquid will be heated to temperature 55 °C\. It is very important not to cross that temperature\. Because the electronic plates are stuck, too large temperature of solution may cause plates unstick and also cartridge electronic damage\.Injecting liquid inside the cartridge it is necessary to remember to suck off using syringe with suction device after about 10 minutes\.
CAUTION:
We receive the largest effectiveness when the liquid is heated to 55 °C\. Don´t cross that temperature\.
Procedures with solid print heads \(Epson models\)\.
Proceed according to the following recommendations:
Start printing
During printing, take out plug from power cord \(the print head should be in a central position\)
Cut out a piece of cloth in the shape of print head
A piece of cloth must be soaked with liquid
put it on the park place \(usually at the right side of the printer\)
Shift the print head in the park position
Wait about 30 minutes
Remove a piece of cloth
Plug the printer in\.
EAN:0
